Welcome Guest ( Log In)

 
 Reply to this topicStart new topicStart Poll

Outline · [ Standard ] · Linear+

> Sheetmetal, unfolding part

Daniel Catlin
post Mar 9 2007, 10:03 AM
Post #1


Block
*

Group: Expired
Posts: 29
Joined: 30-September 04
From: Portsmouth, UK
Member No.: 16,589
Hi,
I am trying to unfold a sheetmetal part after putting a cut across it but every time I unfold it I end up with an extra section that should not be there. I can draw the profile and do the cut but I can't unfold it properly.

Hope you can help.

Regards
Danny

Attached File(s)
Attached File  hr_pvc.ics ( 176k ) Number of downloads: 437
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
tlehnhaeuser
post Mar 9 2007, 10:44 AM
Post #2


TriBall
********

Group: Channel Partners
Posts: 5,691
Joined: 17-October 01
From: Commack, New York
Member No.: 48
Can't doenload file, but did you try to change part ot ACIS?
tom
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Daniel Catlin
post Mar 9 2007, 11:14 AM
Post #3


Block
*

Group: Expired
Posts: 29
Joined: 30-September 04
From: Portsmouth, UK
Member No.: 16,589
QUOTE(tlehnhaeuser @ Mar 9 2007, 09:44 AM)
Can't doenload file, but did you try to change part ot ACIS?
tom
*



I take it I change it to ACIS via the options menu.

I'll give it a go and let you know.

Heres the file again.

cheers
Danny

Attached File(s)
Attached File  hr_pvc.ics ( 180k ) Number of downloads: 497
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cary OConnor
post Mar 9 2007, 12:00 PM
Post #4


TriBall
********

Group: IronCAD Employees
Posts: 5,615
Joined: 23-August 04
Member No.: 17
There are two issues:
1- There is a small segment in the sketch (look at the end of the curve closest to the 0,0). Delete that and reconnect curve 1 and curve 2&3.
2. Once you reconnect it, add a tangency constraint between curve 1 and 2.

Attached is the corrected file.

Attached File  hr_pvcfixed.ics ( 145k ) Number of downloads: 238


Cary
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Daniel Catlin
post Mar 12 2007, 05:38 AM
Post #5


Block
*

Group: Expired
Posts: 29
Joined: 30-September 04
From: Portsmouth, UK
Member No.: 16,589
QUOTE(Cary OConnor @ Mar 9 2007, 11:00 AM)
There are two issues:
1- There is a small segment in the sketch (look at the end of the curve closest to the 0,0). Delete that and reconnect curve 1 and curve 2&3.
2. Once you reconnect it, add a tangency constraint between curve 1 and 2.

Attached is the corrected file.

Attached File  hr_pvcfixed.ics ( 145k ) Number of downloads: 238


Cary
*



Thanks Cary,

Can't open the file though


Danny
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cary OConnor
post Mar 12 2007, 09:51 AM
Post #6


TriBall
********

Group: IronCAD Employees
Posts: 5,615
Joined: 23-August 04
Member No.: 17
It was saved in 9 PU1.
Cary
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Daniel Catlin
post Mar 13 2007, 06:39 AM
Post #7


Block
*

Group: Expired
Posts: 29
Joined: 30-September 04
From: Portsmouth, UK
Member No.: 16,589
Thanks Cary,
I can see what I did now (or didnt do biggrin.gif )


Regards
Danny
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 

Reply to this topicTopic OptionsStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 

All content copyright IronCAD 2000-2008 Low-Bandwidth View Time is now: 23rd May 2013 - 08:09 AM